She Had A Dream...

As you may have noticed, I haven't posted in a while - November 1st seems like such a long time ago! But once I was finished with all the 3D printed kitchen stuff, I had to take a breather. I got my craft space ready for mini work again, and I began to think about what I'd like to do next. Finishing the Willowcrest kitchen seemed like the obvious choice (it's the project that sparked the 3D kitchen accessories to begin with), but I just couldn't muster any motivation to get going on it. In the meantime, I was contacted with a request to design and create a couple architectural elements for a very special project that had been waiting in someone's basement for a very long time.

You may remember my customer, Diana, from my doing her Breakfast At Tiffany's brownstone windows and door replicas last year. One of the projects she's been dreaming about since the 90's is recreating the historically significant Dexter Avenue Baptist Church in Montgomery Alabama. Back then she purchased the Real Good Toys Country Church Kit at a miniatures show to house it in. Then she had custom stained glass windows made by a miniature stained glass artisan. But, like for many of us mini dreamers, other projects moved ahead in line and there the kit sat, waiting for its turn. The project was never truly forgotten. Diana collected a whole lot of lovely resin sitting folks all decked out in their Sunday best to add to the congregation over the years. When she saw the project on it's basement shelf a few months ago while looking for something else, these patient people reignited her inspiration!

What Diana wanted me to tackle was the elaborate carved doorway behind the pulpit, as well as the lattice panel behind the organ area. It was challenging, as the only details I had to go by were the limited photos found on the web. The proportions and measurements had to be estimated. Additionally, Diana only had 10" of  ceiling height (minus the height of her crown molding), and I estimated the doorway in the original church to be about 18 feet tall! I would need to find a way to pay homage to the original within the height limitations, while still balancing the proportions and ending up with something that was worthy of being a focal point in her project.

Challenge accepted! Diana and I traded ideas back and forth on three slightly different models before we both agreed the version below was perfect! It kept the proportions balanced, included as many of the carved details as space would allow, and finished up at 9-7/16" tall by 6-13/16" wide. 

I got to experiment with creating dental molding and fluted columns for the first time with this doorway, and I had so much fun figuring it out!

I am so fortunate that Tasha and Ande gifted me the bigger 3D printer for my birthday last year! My first printer would not have been able to accommodate this big job, other than in pieces needing to be assembled post production.

I think the doorway is so pretty, and I just love how the dental molding, fluted columns and corbels turned out! 

The lattice piece was pretty challenging, too. In scrutinizing the church photos online, I realized that it was created in three panels. The middle panel is slightly shorter which allows room for the wood molding of the lower organ area. It is installed in a raised position on top of and joining the other two panels. The lattice detail itself is done in four levels, not including the main frame and the stepped picture frame molding on top of that. It was a challenge not only to create, but to figure out how to engineer it for a successful print. I felt that eliminating the half circles in the homage version gives the piece more balance and accommodates better the measurements that Diana had to work with.

Level detail close up.

It was such an honor to be trusted with this piece of the job and to help Diana realize her longtime dream!

In other exciting news, I have been busy rediscovering cooking joy with our new Instant Pot! Even Russ has joined in the culinary delight around here! This is all thanks to our big hearted and generous son, Ande! He uses my Prime membership from time to time, and if I leave stuff in my cart and he sees it, he likes to surprise me with it! 💗 This time, it was the Instant pot and accessories I was considering. What a great kid we made!!! He and Lex and Tasha and Brent love theirs, too!

We have run out of fingers and toes counting our blessings, among them, going to Tasha and Brent's new home for their first Thanksgiving there! I hope each of you has more to be thankful for than digits, too!

Happy Thanksgiving!

xo xo,

Jodi

The Replicator

Last week we began our Willowcrest journey by starting on the first/second floor stairwell. I wanted to make that area more viewer friendly by adding a much larger window using the kit's French Door Window as the model. But how could I replicate the fancy, multi-layer and double arched frames and trim? I'm not a woodworker, but I do have lots of technology at my fingertips, so I decided to see what I could do with it. 

3D Printed Staircase Interior Window Frame

After some tinkering, I found that I could scan the frames into my PC, open them in Inkscape, separate the layers then save the best one as an svg file. I imported the svg file into Tinkercad, made adjustments, if necessary, added details and then prepared them for 3D printing. It's a pretty complicated process at first, but once I did a little troubleshooting, I ended up with some amazing replacement kit pieces!

Scanned French Door frames into my PC

Imported into Inkscape and converted into an svg

Imported into Tinkercad. There were mysterious "holes" that needed patching up.

Not only can I combine each of the layers into one frame, to further enhance the kit's components, I can add architectural details created by myself or by others on Thingiverse, Has your mind just exploded like mine did? Oh the possibilities!

The kit has you stack four layers of die cut plywood to achieve the look of fancy molding. Here's what the kit's French Door Window looks like assembled. It's super charming but the plywood needs so much TLC...

French Door Window exterior frame layers.

And here is the Small Window's wooden parts, exterior and interior.

Small Window exterior frame layers.

Small Window interior frame.

Not every piece of plywood in the kit was in great shape. You see, while all the sheets looked to be in good shape at first glance, upon further inspection, while popping out pieces, a couple sheets weren't so good at all. It was as though the top and bottom layers of plywood were nearly petrified and so hard to cut through, even with a sharp Xacto blade. By extreme contrast, the center layers of plywood had disintegrated, leaving a crumbled chasm. This made the pieces very unstable, so tricky to safely remove from the sheets and some had weirdly expanded in thickness. I probably could have restored them with a lot of wood glue, filler, sanding and copious patience, but 3D printing them seems like much more fun. Not only is this method an exciting way to replicate the kit's windows and other trim elements to improve them, it's a way to replace them altogether, when necessary.

French door frame from sheet 4.

French door frame from sheet 7

Here, each layer of the Small Window's exterior frame has been scanned, saved as an svg and imported into Tinkercad.

The kit has you stack four layers to achieve the look of fancy molding.

In Tinkercad, I stacked the frames into one piece and then embellished them with corbels. I added a recessed reveal in the openings so it appears as though the window can open.

A close up view of the 3D rendering which shows the corbel detail better.

For the Stairwell's exterior window,  I added a shelf to the bottom shaped to mimic the window's curves. It's supported with detailed corbels. The same top corbel will be used wherever possible to unify the exterior style. 

Shelf Detail

When I recreate the French Door Window frame for the front of the house I'll skip the shelf and add a frieze to the lower portion since it sits on the porch floor.

The French Door Window to the left of the front door.

All the window "glass" will mount in the exterior window frames. I have created a recess for the "glass" so that the window frame can sit flush to the wall. I'll replace the kit's acetate windows with 1/32" Lexan.

But aren't I getting WAY ahead of myself with all these windows? Yes, but recreating them is so much fun! My goal was to get the entryway/stairwell completed first. The exterior window frames won't be needed until much, much later. All I need right now are the interior stairwell window frame and a small interior window frame for the second floor landing. I went a little crazy with the details on the stairwell frame as you can see. The entry/stairwell is the first room guests see, so traditionally in homes of that era, they were meant to make an impression.

Stairwell window frame.

Side detail.

The interior frames for the rest of the house will likely be a lot more subdued.

Small Window Interior Frame

Side detail.

Here I must digress a little...

Some of you may remember that last fall I worked on a commission to design and print 3D windows and doors for a Breakfast At Tiffany's themed dollhouse. For the 9" door surround, I had to print it in five pieces because of the 5.5" size limitation of my 3D printer's print bed. 

Rendering pieces, left. Printed and assembled door, center. Original BAT door, right.

My supportive husband, believing in my ability to create great things if I have the right tools, conspired with my kids to join forces and buy me a much larger 3D printer for my birthday last December. Now, I am able to print things over twice that large, making it possible for me to print the 7.91" interior stairwell window frame in one piece. Have I ever mentioned how wonderful Russ and my kids are to me? 💗 Using the scan/svg/3D printing method, I can replicate almost any piece I need to, as long as I can fit it onto the X-Max's 300 x 250 x 300 mm (11.81" x 9.84"x11.81") bed. I can even have another small job going at the same time because I still have my trusty old X-one2!

Welcome to the family, X-Max!

Back to windows... Now it was time for the real test. How would the frames look printed? I started with the staircase wall's interior frame. This was pretty complicated, so I figured if this one was successful, I was home free. I think it came out amazingly good, and surprisingly, even with the more capable printer, it took over nine hours to print. I am sure there are settings I can adjust to speed things up, but I still have A LOT to learn! I am trying to eat this elephant one bite at a time.

There is a bit of post production work to do, but sanding PLA is generally pretty easy if you have the right sized sanding implements. And trust me - it is a lot easier sanding than those crumbling plywood frames! And, no slivers!

It looks perfect against the pattern I traced on the wall, so I guess it's safe to cut the hole. Scroll saw here we come! But first...

In my excitement about the windows, I'd nearly forgotten that I also needed to have the front door ready. The kit's door is a double opening model which seems to be a common feature for second empire homes. I thought that re-designing mine to look like a double door but actually opening as one solid door was a better idea - less hinge engineering and less operating parts that could break.  Here's the rendering of what the door and frame looks like together.

Kit's Double Door

I designed it so that it looks the same on both sides. There's a frame for the exterior and the interior. The door itself is printed in two halves that when combined, will be the thickness of the original kit's door. I made a recess for the "glass" so that it will be sandwiched between the door layers. Because of the width, I printed the file two times - one for the interior and one for the exterior. I think I've figured out a way to engineer the hinges and I hope it works! 

Recess for "glass"

And here are the interior/exterior doors printed. I am super happy with how they came out! Each side took over 10 hours.

Test Fit...

From the front porch

From the kitchen doorway. I left 1/32" allowance on each side for paint and swing space.

From the stairs

And the interior Small Window frame straight off the printer. Simple but elegant, I think.

I did the entry arches for the kitchen and living room, too, but haven't printed them yet. First I have to decide on the flooring. The height of the arches will have to be adjusted accordingly for it. And I think it might be time to actually glue the foundation, front wall and center walls in place. Scary and exciting!

My recreation system is not quite as sophisticated as The Replicator in the Star Trek series, but it works well enough for me! And it goes to show that with a little technology and a will to try, any challenge can become an opportunity for even better minis!

Hope you're finding ways to turn your challenges into opportunities, too!

xo xo,

Jodi